Non Destructive Testing In The Aerospace Industry

Non Destructive Testing In The Aerospace Industry Since several years, technology has been improved tremendously and is still in a need for advancement due to the increasing growth of demands. In todays economy structures must remain for operation for such longer period than originally anticipated. The ageing effect on these structures is becoming significant. Non-destructive testing  (NDT) is a wide group of analysis techniques used in science and industry to evaluate the properties of a material, component or system without causing damage  Because NDT does not permanently alter the article being inspected, it is a highly-valuable technique that can save both money and time in product evaluation, troubleshooting, and research. Common NDT methods include  ultrasonic,  magnetic-particle,  liquid-penetrant,  radiographic and  eddy-current testing. NDT is a commonly-used tool in  forensic engineering,  mechanical engineering,  electrical engineering,  civil engineering,  systems engineering,  aeronautical engi neering,  medicine, and  art.(3) The development of Non destructive testing examines the techniques to verify the conditions of these structures and these developments are focused on extending the cost of maintenance of the existing structures. History: It may be said that NDT has been used from ancient times. The audible ring of a Damascus sword blade would show the indication of the strength of the metal in combat. This technique was also used by the early blacksmiths. They used to listen to the ring of different metals being shaped. The same technique was also used by early bell makers. Visual testing had been used for many years for a wide range of applications. Heat sensing was used to monitor thermal changes in materials and sonic tests were performed years ago(1). NDT by far is a visual testings which is the oldest mankind testing, this was used for visual checking knifes. The first use of NDT was done by a English man S.H.Saxby . who used compass for finding cracks in gun pipes in 1868.With a long established history in non-destructive testing (NDT), producing its first UV meter in the late 1960s (as Levy West Laboratories), AST is the market leader with the Levy Hill MkVI meter. NDT is well known as a part of industrial procedures, but it is also of importance in examinations of a more general interest in everyday life. In the aerospace industry, NDT can make the difference between life and death. Aircraft components are inspected before they are assembled into the aircraft and then they are periodically inspected throughout their useful life. Aircraft parts are designed to be as light as possible while still performing their intended function. This generally means that components carry very high loads relative to their material strength and small flaws can cause a component to fail. Since aircraft are cycled (loaded and unloaded) as they fly, land, taxi, and pressurize the cabin, many components are prone to fatigue cracking after some length of time. Even parts that are loaded well below the level that causes them to deform can develop fatigue cracks after being cycled for a long time. Cracking can also occur due to other things like a lightning strike. Aircraft have some protection against lightning strikes but occasionally they occur and can results in cracks forming at the strike location. The historical development of NDT is outlined for each technique. The second oldest method was the Acoustics it has been used by ancient time when man started making the pottery vessels. Table1. Table below shows a list of some of the key events in the chronology of NDT. (1) Year Chronology of Early Key Events in NDT 1800 First thermography observations by Sir William Herschel 1831 First Observation of electromagnetic induction by Michael Faraday 1840 First infrared image produced by Herschels son, John 1868 First reference to magnetic particle testing reported by S.H. Saxby, by observing how magnetized gun barrels affect a compass 1879 Early use of eddy currents to detect differences in conductivity, magnetic permeability, and temperature initiated by E. Hughes 1880-1920 Oil and whiting technique, forerunner of present-day penetrant test used for railroad axles and boilerplates 1895 X-rays discovered by Wilhelm Conrad Roentgen 1898 Radium discovered by Marie and Pierre Curie. 1922 Industrial Radiography for metals developed by Dr. H.H. Lester. 1927-28 Electric current induction/ magnetic field detection system developed by Dr. Elmer Sperry and H.C. Drake for the inspection of railroad track. 1929 Magnetic particle tests/ equipment pioneered by A.V. deforest and F.B. Doane. 1930 Practical uses for gamma radiography using radiumwere demonstrated by Dr. Robert F. Mehl 1935-40 Penetrant techniques developed by Betz, Doane , and deForest 1935-40 Eddy current developments by H. C. Knerr, C. Farrow, Theo Zuschlag, and Dr. F. Foerster 1940-44 Ultrasonic test metod developed in United States by Dr. Floyd Firestone 1942 First Ultrasound flaw detector using pulse-echo introduced by D.O. Sproule 1946 First portable ultrasonic thickness measuring instrument, the Audigage, was introduced by Branson 1950 Acoustic emission introduced as an NDT method by J. Kaiser Mid 1950s First ultrasonic testing immersion B and C scan instruments developed by Donald C. Erdman From the late 1950s to present, NDT has seen many developments, innovation, and growth. The roots of non-destructive testing began to take form prior to the 1920s. In the 1920s there was an awareness of some of some of the magnetic particle tests, the visual test and also X-radiography. Prior to World War II, design engineers were content to rely on unusually high safety factors which were usually built or engineered into many products. In addition, there were a significant number of catastrophic failures and other accidents relating to product inadequacies that bought the concern for system and component quality to the forefront. (1) Background History of Individual Testings: Magnetic Particle Test: Saxby used a magnetic compass to locate the defects and in homogeneities in gun barrels in 1868. Herring in 1879 obtained a patent in United States for the defection of defects in railway lines using a compass needle. Deliberate studies were carried out by A.V. de Forest in 1928 and 1929 of the use of magnetic particles for non-destructive testing of ferromagnetic materials. In 1936, Unger and Hilpert described in a patent in Germany at where the inspection of aircraft engine parts, engines for fatigue cracks are developed rapidly and the magnetic particle testing was made mandatory. The real breakthrough for magnetic particle testing came, in 1960s these methods was further greatly developed by C.Betz. Radiography: Wilhelm.Conrad. Roentgen discovered X rays in 8 November 1895 when it was observed by him that fluorescent glow of crystals on a table near the cathode ray tube. Later the penetrating radiations were characterized systematically which are emitted by cathode ray tubes. These represent the very first radiographs taken in 1896. He conducted a test on his own hunting rifle. Radiograph of the rifle showed some defects in the material and was the start of industrial radiography. Penetrant Test: It is a simple and effective method of examining surface areas for defects, cracks and discontinuities. Rubbing of carbon black on glazed pottery is one of the early surface inspections. Later on in 1940 magnetic particle method was introduced which is more sensitive. Many of the earlier developments were carried out by Magnaflux, IL USA. In 1942 it introduced Zyglo system where the fluorescent dyes were added to the liquid penetrant. The methods were formerly called The oil and whiting method and were used by the huge locomotives in the beginning of the 20th century.(13) Ultrasonic testing: Richardson proposed Echo ranging detection of objects at sea in 1912. Later, Lavengin developed a source of ultrasonic waves by using the piezoelectric effect with quartz crystals between steel plates. Future on experiments was carried out by Boyle and by Wood by using quartz piezoelectric transducers. The most simple and quick method came up in 1940 by Firestone. The method avoided many of the problems which were associated with standing wave formation. Then in 1942 Firestone was the first to use his own method for the sonar. The two German brothers H and J. Krautkramer did a lot of research of method and contributed for the development of method. Since their time method has gone through several phases of development. Eddy Current Test: Jean-Bernard Leon Foucault is generally credited with the first clear demonstration of eddy currents, by showing that electrical currents are set up in a copper disk moving in a non uniform magnetic field. Hughes is considered to have been the pioneer in using Eddy currents to inspect the metals. Eddy currents are also known as Induced currents which can only exist in conducting materials.(13) The use of NDT methods took place during the Second World War started from the testings of submarines and airplanes. During these years the use of NDT is seen in the inspection of nuclear power plant components, pressure vessels and car parts. Aim: To investigate the use of various NDT methods in industry. Objectives: To Conduct research on NDT and its applications To identify key components of an aircraft, where likely hood of crack is high. To test the components with appropriate NDT methods. To perform penetrant test to identify the cracks in a gear. Initial Plan As the project initiates with the major task of carrying out the background reading and researching, great amount of time has to be required to collect information about project. A great deal of time has been spent on background reading. Project requires thorough knowledge on NDT in aerospace and its classification. A detailed background reading has been done to understand the concept of NDT. Background reading has also been done on different types of NDT testings and its classifications. A detailed study has been done on the history of NDT. Background Reading: Non Destructive Testing (NDT) Non-destructive testing is the process by which materials, components or assemblies can be inspected without affecting their ultimate serviceability. It offers some important advantages over destructive testing processes such as mechanical testing. A destructive test must necessarily be on a sample basis. This is acceptable in many cases: to check that a batch of material is within specification, for example, or as a sample check on a large number of identical components. But a sample destructive test may not be feasible for a small number of high value components and in critical cases a 100% inspection may be required. Because of this, one key role of NDT is in assuring the quality of many manufacturing processes. NDT can also be used to test components which have been subjected to service conditions. A welded structure can be inspected to detect fatigue cracking. NDT results can further be used to aid decisions on the need for and timing of repairs. Suitable techniques, correctly applied, can be used to measure the depth of a fatigue crack. This, coupled with knowledge of the system stresses, the toughness of the material and the fatigue crack growth rate, can be used to determine if a cracked component can be left in service until the next planned overhaul period. These twin roles of NDT ensure that the technology will continue to play a fundamental role in materials testing.  Aircrafts are designed to withstand a certain amount of damage from cracking and corrosion without cause for concern, and NDT inspectors are trained to find the damage before it becomes a major problem.  The rigorous process used to design aircraft either allows for a certain amount of damage to occur before a part fails, or in many cases, a part can fail completely and performance of the aircraft will not be affected. The job of the NDT inspector is to find the damage while it is within acceptable limits.(5) Role of NDT Non destructive testing can be taken place at any transportation industry. The main aim is to consider the over view of all the terms of NDT and its applications and also to consider research on the optical methods. This is considered to be one of the important terms in the project. Another term is to do research on the optical methods which are implemented on the aircraft parts. (12) Types of methods: The number of NDT methods that can be used to inspect components and make whether the measurements are large and continues to grow. Researchers continue to find new ways of applying physics and other scientific disciplines to develop better NDT methods. However, there are six NDT methods that are used most often. These methods are visual inspection, penetrant testing, magnetic particle testing, electromagnetic or eddy current testing, radiography, and ultrasonic testing. These methods and a few others are briefly described below. (12) Visual and Optical Testing (VT)   Visual inspection involves using an inspectors eyes to look for defects. The inspector may also use special tools such as magnifying glasses, mirrors, or bore scopes to gain access and more closely inspect the subject area. Visual examiners follow procedures that range from simple to very complex. The principle behind Visual testing is the use of reflected or transmitted light from test object that is imagined with the human eye or other light-sensing device. VT finds its application in many industries ranging from raw materials to finished products and in-service inspection. VT can be inexpensive and simple with minimal training required. It has broad scope of uses and benefits. However VT can only evaluate surface conditions. Also effective source of illumination is required. (1) Penetrant Testing (PT) Test objects are coated with visible or fluorescent dye solution. Excess dye is then removed from the surface, and a developer is applied. The developer acts as blotter, drawing trapped penetrant out of imperfections open to the surface. With visible dyes, vivid colour contrasts between the penetrant and developer make bleed out easy to see. With fluorescent dyes, ultraviolet light is used to make the bleed out fluoresce brightly, thus allowing imperfections to be readily seen. (6) Figure1: Figure illustrating a simple Penetrant testing (8) The principle behind PT is that a liquid containing visible or fluorescent dye is applied to the surface and the fluid enters the discontinuities by capillary action. PT finds its application in virtually any solid non-absorbent material having uncoated surfaces that are not contaminated. PT is relatively easy and materials are inexpensive. It is extremely sensitive and very versatile. Also minimal training is required. Discontinuities can only be found on the surface. The surface condition must be relatively smooth and free of contaminants. (1) Magnetic Particle Testing (MT)HYPERLINK http://www.ndt-ed.org/EducationResources/CommunityCollege/MagParticle/cc_mpi_index.htm   This NDE method is accomplished by inducing a magnetic field in a ferromagnetic material and then dusting the surface with iron particles (either dry or suspended in liquid). Surface and near-surface imperfections distort the magnetic field and concentrate iron particles near imperfections, previewing a visual indication of the flaw. (6) Figure2. Figure illustrating the basic concept of Magnetic Particle Testing (9) The principle behind MT is that the test particle is magnetized and fine ferromagnetic particles are applied to the surface, hence aligning at discontinuity. MT finds its application in all ferromagnetic materials, for surface and subsurface discontinuities. It can be used in large and small parts. MT is relatively easy to use. Equipment and material is usually inexpensive. MT is highly sensitive and fast compared to PT. However in MT only surface and a few subsurface discontinuities can be detected. The test can be only done on ferromagnetic materials. (1) Electromagnetic Testing (ET) or Eddy Current Testing Electrical currents are generated in a conductive material by an induced alternating magnetic field. The electrical currents are called eddy currents because they flow in circles at and just below the surface of the material. Interruptions in the flow of eddy currents, caused by imperfections, dimensional changes, or changes in the materials conductive and permeability properties, can be detected with the proper equipment. Figure3: Figure illustrating Eddy Current Testing (10) The principle behind ET is that localised electric fields are induced into a conductive test specimen by electromagnetic induction. ET finds its application in virtually all conductive materials. All conductive materials can be examined for flaws, metallurgical conditions, thinning and conductivity. ET is quick, versatile, and sensitive. It can be no contacting. Also it can be easily adaptable to automation. However variables must be understood and controlled. (1) Radiography (RT)HYPERLINK http://www.ndt-ed.org/EducationResources/CommunityCollege/Radiography/cc_rad_index.htm   Radiography involves the use of penetrating gamma or X-radiation to examine parts and products for imperfections. An X-ray generator or radioactive isotope is used as a source of radiation. Radiation is directed through a part and onto film or other imaging media. The resulting shadowgraph shows the dimensional features of the part. Possible imperfections are indicated as density changes on the film. Figure4: Figure illustrating the basic principle of Radiographic Testing (11) The principle behind RT is that a radiographic film is exposed when radiation passes through the test object. RT finds its application in most material, shapes and structures. RT is the most widely used and accepted volumetric examination. RT can used only on limited thickness based on material density. Also there is a possible threat of radiation hazard.(1) Ultrasonic Testing (UT)HYPERLINK http://www.ndt-ed.org/EducationResources/CommunityCollege/Ultrasonics/cc_ut_index.htm   It uses transmission of high-frequency sound waves into a material to detect imperfections or to locate changes in material properties. The most commonly used ultrasonic testing technique is pulse echo, wherein sound is introduced into a test object and reflections (echoes) are returned to a receiver from internal imperfections or from the parts geometrical surfaces. Figure5: Figure illustrating the basic concept of Ultrasonic Testing (11) The principle behind UT is that high frequency sound pulses from a transducer propagate through the test material, reflecting at interfaces. Most materials can be examined if sound transmission and surface finish are good and shape is not complex. UT provides precise, high-sensitivity results quickly. Thickness information, depth, and type of flaw can be obtained from one side of the component. (1) Work to date As suggested by the project plan, the entire duration of the project is distributed variably as required by different tasks commencing from the basic research and reading. According to the project plan the research was done on few NDT techniques and some of the techniques are still under research, along with types of methods and its techniques. Necessary Future Work A more detailed and precise study of non destructive testings in aero industry is to be done. Project requires identifying various testings in Aerospace industry. A detailed study should be done on techniques and testings of NDT in Aerospace industry. A precise study of industrial applications and research should be done on optical methods. Key components of an aircraft should be identified and finally components may be tested by appropriate NDT methods. The main project work to be done is perform a Dye Penetrant Testing to identify cracks on gear. Dye penetrant inspection  (DPI), also called  liquid penetrant inspection  (LPI) or  penetrant testing(PT), is a widely applied and low-cost inspection method used to locate surface-breaking defects in all non-porous materials (metals, plastics, or ceramics). The penetrant may be applied to all non-ferrous materials. The main steps in Liquid Penetrant Inspection which are intended to be performed on the gear may be: Pre-cleaning: The test surface is to be cleaned to remove any dirt, paint, oil, grease or any loose scale that could keep the penetrant out of a defect. Application of Penetrant: The penetrant is to be then applied to the surface of the item which is to be tested.   Excess Penetrant Removal: The excess penetrant is to be then removed from the surface. Application of Developer: After excess penetrant has been removed a white developer is to be applied. Inspection: The inspection is to be done using visible light with adequate intensity for visible dye penetrant. Post Cleaning: The test surface is then to be cleaned after inspection and recording of defects. Summary It is clear that NDT has advantage from other inspection techniques as it does not make any changes to the article. It is a highly-valuable technique that can save both money and time in product evaluation, troubleshooting, and research. NDT is very useful in order to detect cracks in materials of magnitude in micrometers. (2) Its aerospace application includes detection of cracks caused due to corrosion, fatigue and their synergistic interactions. Crank shafts, frames, flywheels, crane hooks, shaft, steam turbine blades and fasteners are some of the components which are more vulnerable to fatigue so regular inspection is necessary via NDT method. Typical components which are inspected using NDT method by manufacture in order to maintain quality are turbine rotor disc and blades, aircraft wheels, castings, forged components and welded assemblies. One of the NDT methods is Eddy current technique which can be used to check tube, bar and wire and also this method is automatic and highly sophisticated.(3) It can be said that NDT method has to be carried out in order for the aircraft to operate safely during service time and avoid any accidental damage due to fatigue and corrosion.(2) In this report, a detailed explanation of NDT testings and techniques are explained. The uses of NDT in different industrial applications are explained and a precise study on optical methods is done. According to the project plan, next task would be to conduct research on NDT applications. List of Tables Table1: Table showing a list of some of the key events in the chronology of NDT List of figures Figure1: Figure illustrating a simple Penetrant testing Figure2. Figure illustrating the basic concept of Magnetic Particle Testing Figure3: Figure illustrating Eddy Current Testing Figure4: Figure illustrating the basic principle of Radiographic Testing Figure5: Figure illustrating the basic concept of Ultrasonic Testing

Start Up of New Fast Food Chain in India

Group 3 Member Debashish Das Pallavi Talwar Hari Das Gupta Pramod Balakrishnan Ans Since the maiden business venture would be the first business venture of the group, we would prefer to keep the funding internal. The business venture we would start is Indian Street food restaurant â€Å" Pao Khao† Executive Summary Pao Khao is a locally owned fast food outlet that will be positioned as an international franchise through our creative approach to the company's image and detail presentation. Pao Khao will provide a combination of excellent food at value pricing, with fun packaging and atmosphere. Pao Khao is the answer to an increasing demand for snack-type & Ethnic Indian food. In today's highly competitive environment, it is becoming increasingly difficult to differentiate one fast food outlet from another. Delhi NCR , has population of more than 2 million. Our main priority is to establish starting in Gurgaon , preferably close to one of prominent shopping malls in MG road. Later, our effort will be a further development of more retail outlets in the surrounding area. This plan is prepared to obtain a location for the initial launch of this concept. Additional financing will need to be secured for the two subsequent outlets, anticipated in month 13 and early in year three. The financing, in addition to the capital contributions from shareholders, will allow Pao Khao to successfully open and expand through year two. The initial capital investment will allow Pao Khao to provide its customers with a value-driven, entertaining experience through the creativity of its founders. Pao Khao will entice youngsters as well as working couple (DINK) to bring their friends and family with our innovative environment, fresh Indian Snack /Ethnic food . 1 Objectives †¢To establish a presence as a successful local fast food outlets and gain a market share in Delhi NCR Fastest growing fast food industry. †¢To make Pao Khao a destination spot for mall-goers, leisure & pleasure seekers 1. 2 Mission Our main goal is to be one of the most successful fast food outlets in Gurgaon, starting with one retail outlet located inside a major shopping mall as a â€Å"market tester. † Pao Khao will strive to be a premier local fast food brand in the local marketplace. We want our customers to have the total experience when visiting our outlet(s) and website as they will learn about this fascinating new â€Å"pop culture. † We will sell merchandise from pre-packaged chutney and t-shirts, to innovative combinations such as Idli Dhokla, all with our official brand attached to them. Our main focus will be serving high-quality food at a great value. 1. 3 Keys to Success To succeed in this business we must: †¢Create a unique, innovative, entertaining menu that will differentiate us from the rest of the competition. Control costs at all times, in all areas and implement a conservative approach to growth policy. Although, we provide more than enough fund to open more than one outlet, we want to be on the safe side of the business. †¢Sell the products that are of the highest quality, as well as keeping the customers happy with all of our product categories from food to store merchandising. †¢Provide 100% satisfaction to our customers and maintaining the level of excellent services among other competitors. Encourage the two most important values in fast food business: brand and image, as these two ingredients are a couple of main drivers in marketing communications. †¢Get access to high-traffic shopping malls near the target market. †¢Promote good values of company culture and business philosophy. 2. 1 Company Ownership Pao Khao is a privately held company. It will be registered as a Limited company, with ownership 25% – Hari Das Gupta, 25% – Pallavi, 25% – Pramod, 25% – Debashish 2. 2 Start-up Summary The retail outlet will be rented at one of the target location shopping malls. Our preference is Space A, for the main reason of reaching larger traffic. Startup requirements will be financed through owner investments. (all values in INR) a 2. 3 Company Locations and Facilities Pao Khao locations will range in size from 70~100 meter square and will seat from 15 – 25 guests. Our first location will be on the larger end of this range. The location will feature its own originality in merchandise display and other brand building attributes. We will equip the outlet with modern furniture and aim for cleanliness and an open feeling. We are currently looking at several possible sites in shopping malls along MG Road. The space selection will be chosen based upon the following criteria: †¢Community size: minimum of 10,00,000 people within a radius of 5 kilometers. †¢Office Areas and Tourist destination. †¢Easy access. †¢Large percentage of upwardly mobile upper middle class in the community. All of these qualities are consistent with Pao Khao goal of providing a top quality fast food experience. We want â€Å"word-of-mouth† to be our best form of marketing, where our customers value our brand as something exciting and cannot wait to tell their friends and neighbors. Pao Khao will directly compete with several fast food joints inside the chosen shopping mall, including Mac Donald, Pizza Hut and other but create niche for its ethnic Indian Flavour. Products We want to focus only on selling Indian Food. Alcoholic drinks will not be sold in our outlet, as Pao Khao promotes a healthy and positive Indian lifestyle. 3. 1 Product Description Pao Khao primarily ethnic Indian Street/Snack food †¢Chole Bature †¢Dahi Bhalla †¢Indian Thaali †¢Executive Thali †¢Rajmaa chawal or noodles.. (fusion) †¢Pao Bhaji †¢Dhokla etc 3. Competitive Comparison Pao Khao has several advantages over its leading competitors: †¢Unique â€Å"fusion† concept of Indian Food. †¢We expect a high degree of enthusiasm and offer a fun store with friendly staff, that reflects the company's youthful and energetic culture. †¢Supporting merchandise items that support the company's brand building. †¢Our innovative packaging will be more entertaining than our competitors †¢Direct relation with farmers to procure fresh vegetable and grains at lower prices. Core essential for successful business strategy would be 1. Indentifying appropriate and correct place for the first restaurant. 2. Quality of service and food , cleanliness 3. Commitment to customer and creating the right ambience 4. Chefs are key USP and need to have competency to develop this and also keep in mind attrition due to competition. 5. Marketing – Without proper marketing, howsoever a good idea can fail , hence marketing strategy is paramount importance Marketing has to be both ATL and BTL†¦Since we are promoting amidst fierce competition, we need to have aggressive marketing strategy which creates buzz in

Senior Student

If I were a newly appointed procurement manager at a company or an organization that there has not been yet proper procurement procedure I will try to convince the CEO of that company and organization by raising some importance point related to the procurement procedure. Those include: 1. It is easily to prepare and controlling the budget of the company: it can reduce the waste of spending on unnecessary things by using the fix budget or flexible budget strategy to control over purchasing products. 2.It can avoid of cheat and mistake on purchasing products: after we got that form we can make sure that the product that need to order is well accepted because it has to be check by the officer or CEO to confirm the purchase. 3. It is like a road map to show where the product shall be taken and how the purchase be made. 4. Build good relationship with the suppliers: because we need to select the supplier who we can be trust and can be work with us for long time and realizable so we need t o select the potential suppliers to be the part supplier of our company. . Saving money: after we have the part supplier we can save some money because when we select someone to be our part supplier they will provide us a premium price or when we use bulk purchase. Here is the simple plan diagram of the procurement procedure diagram: 1. Check for the department budget or company budget before request or propose a form. 2. Written a requesting form of what you want to purchase and the purpose of purchasing. 3. Get a signature from the authorization person to validate the purchasing order. 4.Get that requesting form to purchasing department or procurement department to check for the necessity of the product order and the available product in stock or should buy them from the suppliers. 5. After the purchasing has already made up they shall take the requesting form to the financial department to get an approval or a direction where the requesting shall go next. 6. In case if the purcha sing has reach the maximum of financial approval it has to go to the principle officer or CEO to get approval before the purchase can be made or done. 7.After we got the approval next we has to find the ways that the product transport to the department. 8. After the product arrival we need to check for the quantity and quality of the product. 9. Next we should evaluate the supplier performance whether they provide us a good delivery or can be used as the part supplier or not. 10. After that send the product that is done send to user department. Diagram: Check for budget Written a requesting form Get approval by the authorize person Send to purchase or procurement department Send to financial departmentGet approval from the principle or CEO Check for delivery term or strategies Check for the product quality Evaluate the supplier performance Send to the user department Here is the ways to communicate our new procedure for coordinate effectively in the future: 1. Get a signature from t he CEO to approve that our new procedure is legally accepted 2. Take it to the human resource department and ask for the meeting of all team leaders in each department. 3. Explain the entire team leader about the new process nicely in the manner of convincing rather than used the position power. 4.Observe from what they thinking and gather the feedback to adjust in case of the reasonable argument. 5. Hosting an unofficial meeting to maintain the relationship with other team leader by showing them that you pay respect to them and willing to accept the feedback. 6. In case of the convincing is not acceptable we can use the position power by working with the CEO to enforce the procedure so that everybody has to listen. In conclusion as we are the new procurement manager we should understand how to convince people to get your point and what make your speech delivery effectively and catchable to all the audience.

Qualitative Research or Quantitative Research - Which is...

Both qualitative and quantitative research methods have their specific qualities which make them useful to a researcher, however in the course of this short essay I will explain why, for several reasons, qualitative research is better. As both methods operate within different assumptions, it is important to stem criticism for each method s respective theoretical base in order to adequately judge them. In the course of this essay I will highlight each method s theoretical assumptions and then I will assess each method by pointing out their positive and negative factors. The underlying assumption behind qualitative research is that the entire subject needs to be examined in order to understand the phenomenon. Quantitative research†¦show more content†¦14)Compare this with a definition of quantitative research: The aim is to classify features, count them, and construct statistical models in an attempt to explain what is observed. It is objective - seeks precise measurement analysis of target concepts. (Miles Huberman: 1994, p. 40)Both of these definitions contain the term objective, which shows that both of the methods share the core aspect of non-interference with subjects: Content analysis is often referred to as an unobtrusive method (Bryman: 2008, p. 289)This key concept lies at the heart of both content analysis and quantitative research methods, it is an obvious similarity. In Shephard s study of the dynamics between the party, candidates and constituencies he used content analysis on party leaflets to spot recurring trends. His meth od (content analysis) bears a striking resemblance to quantitative research, for example both methods begin with hypotheses and theories, Shephard choosing to ask whether emphasis in leaflets matches the profile of the constituents. He then made two hypotheses stating that -the higher the unemployment rate the higher the emphasis on jobs and job creation and the higher the home ownership, the higher the emphasis on interest rates and mortgages. Quantitative research methods also start off with hypotheses and theories; therefore it is clear to see that content analysis could beShow MoreRelatedQuantitative vs Qualitative Research on which is Better1830 Words   |  7 PagesThere has always been a discussion as to which method of study was better: quantitative, or qualitative. The quantitative approach focuses more on quantifying data and generalizing results from a sample to a population of interest. The use of quantitative methods is used for general features of a population and to measure the incidence of various views and opinions in a chosen sample. Qualitative methods are used to gain an understanding of underlying reasons and motivations. This type of methodRead MoreReasons For Social Science Research Essay1201 Words   |  5 PagesREASONS WHY SOCIAL SCIENCE RESEARCHERS PREFER TO USE QUANTITATIVE METHODS. Introduction: The main purpose of this article is to introduce some important fundamental concepts of quantitative research to readers, especially social science researchers. It comprises types of research, definitions of quantitative research, different types and assumptions of quantitative research, when to use and not to use quantitative methods, advantages, common approaches and samples of quantitative research, and commonRead More Research Methods1483 Words   |  6 PagesAnalyze of research in averagely can be accounted as an aim for understanding or a systematic study in search of information to shape or accept achievable facts. There are two mainly different ways of research. First, there is the basic research that appears not to go into the study field and the second, way is the applied research that studies given area into the aspect. It applies to resolve, understand and advance the methods and systems that are used in the search for human understanding of abnormalRead MoreQualitative And Quantitative Research Methods936 Words   |  4 PagesQualitative and quantitative research methods are two alternative applications for research methods. Both are very different in how data is collected, what data is collected, and how data is measured. Both of these research methods are utilized amongst the major areas of psychology and the social sciences. This paper will provide a brief description of qualitative and quantitative methods, provide the differences between the two approaches along with the terminology used for both; I will alsoRead MoreQuantitative, Qualitative And Quantitative Methodologies804 Words   |  4 PagesIntroduction Along with qualitative and quantitative methodologies in research, the trend of combining both qualitative and quantitative methodologies is widely used and increasingly articulated, attached to research practice and recognized as the third major research approach or research paradigm (Johnson, Onwuegbuzie Turner, 2007). As cited by Anaf and Sheppard (2007), Key in 1997 suggested the theory and meaning, qualitative and quantitative methodologies are distinct. A qualitative methodology’s focusRead MoreQualitative Research And Quantitative Research1675 Words   |  7 Pages Qualitative research and Quantitative research Qualitative research Defilation Qualitative research is a method used in different academic disciplines, generally in social science, but also in research and further contexts. Qualitative researchers aim to attain detailed understanding of human behavior rand the reasons that govern such behavior. The qualitative method investigates the why and how of decision making, not just what, where, when. Hence, smallerRead MoreResearch Methodologies : Questions, Variables, And Data793 Words   |  4 PagesResearch Methodologies: Questions, Variables, and Data Gathering information and conducting research is the starting point when a teacher wants to know a best teaching method or practice. Quantitative and qualitative research can be used for a teacher’s research. If quantitative research is used, three types of questions are available, and are of extreme importance. These types of questions include: descriptive, relational, and causal. It is up to the teacher doing the research to decide howRead MoreThe Social Construction Of Experience1437 Words   |  6 PagesIn particular, qualitative researchers tend to focus more on the social-constructed reality and the contextual influence, interaction and constraints between the researcher(s) and the participants. They are interested in finding answers to questions that focus on the â€Å"social construction of experience and how meaning is created† (Cooper White, 2012, p. 15). However, quantitative researchers â€Å"emphasize measurement and analysis, and focus on product ra ther than process† (Cooper White, 2012, p.Read MoreComparing Quantitative and Qualitative Research1586 Words   |  7 PagesCOMPARING QUANTITATIVE AND QUALITATIVE RESEARCH Social theory is a â€Å"system of interconnected ideas that condenses and organises the knowledge about the social world and explains how it works† (Neuman, 2006, p.8) and for many years scientists have gathered data using specialised techniques such as Quantative and Qualitative research to support or reject these theories. Quantitative research â€Å"generates numerical data or information that can be converted into numbers,† (Experiment Resources, 2009,Read MoreQualitative Research Is Good At Simplifying And Managing Data Without Destroying Complexity And Context956 Words   |  4 PagesQualitative research is good at simplifying and managing data without destroying complexity and context. Qualitative methods are highly appropriate for questions where preemptive reduction of the data will prevent discovery. If the purpose is to learn from the participants in a setting or a process the way they experience it, the meanings they put on it, and how they interpret what they experience, the researcher needs methods that will allow for discovery and do justice to their perceptions and